Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The North Miami Beach Owner’s Guide

Ghost Controls keypad and intercom repair in North Miami Beach typically runs $165-$385 installed, depending on whether we’re replacing the keypad head, the intercom module, or the full entry station. We stock Ghost Controls-compatible keypads and intercom boards on the truck and can usually complete the swap same day once we confirm your gate’s exact model. Most homeowners discover the failure when a code stops working, the speaker crackles out, or the keypad lights up but the gate won’t move.

Call (754) 219-6080

North Miami Beach is hard on these parts. The salt air off Dumfoundling Bay works its way into the keypad membrane and the intercom’s microphone housing within two or three years. What starts as a sticky button becomes a dead column of numbers, then a keypad that only responds half the time. By the time people call us, they’ve usually reset the code twice and replaced the battery once. The real problem is usually inside the unit.

Which Ghost Controls Models This Applies To

Ghost Controls uses two main keypad generations. The older AXS1 and AXS2 series shipped with entry stations that had a gray plastic face and exposed screws on the housing. The newer AXP1 and TSS1 lines moved to a sealed keypad face with an integrated intercom speaker behind a small grille at the top. The mounting footprint is different between generations, which means you can’t drop a new keypad head onto an old backplate without drilling fresh holes.

Here’s the compatibility gotcha we see regularly in North Miami Beach: Ghost Controls intercom modules for the AXP1 series are not backwards-compatible with the AXS1 wiring harness. The connector changed from a four-wire screw terminal to a six-pin molex plug. If someone hands you a new intercom board and your gate was installed before 2018, the plug won’t seat. We keep both generations on the truck so the repair doesn’t stall.

On the OEM-versus-aftermarket question for Ghost Controls specifically: the OEM keypads use a UV-stabilized silicone membrane that holds up better in Florida sun than most budget aftermarket equivalents. We’ve installed aftermarket heads that looked identical and started yellowing within six months. For the keypad face we quote OEM by default. For the intercom board, a quality aftermarket equivalent from a supplier we’ve vetted since 2014 is often $40-$60 less and functions identically. We’ll show you both options and the written price for each before anything gets ordered.

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

• Keypad accepts the code but the gate won’t open. This usually means the relay inside the keypad is no longer closing. The keypad thinks it’s working because the backlight and beeper still fire. The gate operator never receives the signal.
• Intercom speaker buzzes or sounds like it’s underwater. The speaker cone degrades in the salt air off Dumfoundling Bay. Over time, the paper cone separates from the voice coil. You’ll hear a scratchy, low-volume voice that cuts in and out.
• One column of keys stops responding. The membrane contact sheet inside the keypad has a burned trace. This almost always starts with a single column or row. People think they pressed the wrong code, but the pad physically can’t send that digit.
• Keypad lights up intermittently or not at all. The power feed from the gate board is dropping. Sometimes it’s a corroded wire at the terminal block; sometimes the keypad’s voltage regulator is failing. Either way, the fix is in the circuit, not the battery.
• Visitor presses the call button and nothing happens on your end. The intercom’s push-to-talk switch fails first on Ghost Controls units. It’s a small tactile switch that gets gummed up with salt and humidity. The speaker and board are fine, but the button never closes the circuit.

Before

After

Replacement Cost & What’s Included

In North Miami Beach, a Ghost Controls keypad replacement runs $185-$275 installed. A full entry station with keypad and intercom runs $310-$385 installed. The intercom module alone falls between $165 and $225 depending on which generation your gate uses. These are the written prices we hand you before work starts – the number doesn’t move after the fact.

Every repair includes the part, the labor, the wiring check at the gate operator, and a programming test so your entry codes still work. We photograph the old part, the new part, and the final wiring before we leave. The 365-Day Done Right Promise covers the work for a full year. If the keypad acts up again in that window, we return and make it right at no charge.

DIY or Call Us?

This is a low-voltage part, so the electrical risk is minimal. You can safely unscrew the keypad face and check for corrosion on the terminal screws. That’s worth doing once. What you shouldn’t do is try to open a sealed Ghost Controls keypad head and reseal it with silicone. The membrane needs an airtight seal to survive even one rainy season in North Miami Beach, and a resealed unit usually fails within months.

Where DIY goes wrong is in the diagnosis. We’ve arrived at homes where the owner replaced the keypad, then the intercom board, and the problem was a corroded wire six inches from the operator. They spent $300 on parts to avoid a $110 wiring repair. If you’re not certain which part failed, call (754) 219-6080. We’ll diagnose it, show you the failed component, and give you a written price before any work starts. Adrian Vance has been running these calls across North Miami Beach long enough to tell you that guessing costs more than a service visit.

FAQs